Shandong · Yantai
Specification of GZM Series Conical Ball Mill
| Model | Barrel | Effective Volume(m³) | Ball Load(t) | RPM(r/min) | Motor Power(kw) | Weight(t) | |
| Dia.(mm) | Length(mm) | ||||||
| GZM0912 | φ900/φ675 | 900/300 | 0.7 | ≤1.0 | 41.6 | 11 | 4.3 |
| GZM0916 | 1350/300 | 0.8 | ≤1.4 | 41 | 15 | 4.9 | |
| GZM0918 | 1500/300 | 0.9 | ≤1.5 | 41 | 15 | 5.1 | |
| GZM0921 | 1800/300 | 1.1 | ≤1.7 | 41 | 18.5 | 5.5 | |
| GZM1216 | φ1200/φ900 | 1200/400 | 1.7 | ≤2.9 | 36.4 | 22 | 6.5 |
| GZM1220 | 1600/400 | 2.2 | ≤3.7 | 36.7 | 30 | 7.3 | |
| GZM1224 | 2000/400 | 2.6 | ≤4.5 | 36.7 | 37 | 9.3 | |
| GZM1226 | 2200/400 | 2.9 | ≤4.9 | 36.7 | 37 | 9.7 | |
| GZM1228 | 2400/400 | 3.1 | ≤5.3 | 36.7 | 45 | 10.3 | |
| GZM1520 | φ1500/φ1200 | 1500/500 | 2.8 | ≤4.9 | 31.6 | 45 | 12.9 |
| GZM1523 | 1800/500 | 3.3 | ≤5.7 | 30.9 | 55 | 13.9 | |
| GZM1526 | 2100/500 | 3.8 | ≤6.5 | 30.9 | 55 | 14.7 | |
| GZM1529 | 2400/500 | 4.2 | ≤7.2 | 30.9 | 75 | 16.9 | |
| GZM1530 | 2500/500 | 4.4 | ≤7.2 | 30.9 | 75 | 17.0 | |
| GZM1535 | 3000/500 | 5.1 | ≤8.6 | 30.9 | 75 | 18.6 | |
| GZM1541 | 3635/465 | 6.1 | ≤10.5 | 29.5 | 95 | 20.2 | |
| GZM2127 | φ2100/φ1670 | 2500/600 | 8.6 | ≤14.8 | 24.1 | 155 | 36.5 |
| GZM2131 | 3000/600 | 10.1 | ≤17.4 | 24.1 | 180 | 41.0 | |
| GZM2727 | φ2700/φ2287 | 2150/550 | 12.9 | ≤22.9 | 21.6 | 210 | 55.9 |
| GZM2733 | 2750/550 | 15.9 | ≤28.0 | 21.6 | 245 | 62.4 | |
| GZM2740 | 3450/550 | 18.3 | ≤31.4 | 21.3 | 320 | 70.8 | |
| GZM2742 | 3650/550 | 20.5 | ≤36.6 | 21.7 | 320 | 71.3 | |
Note:
(1) The maximum capacity feeding steel ball is determined according to 40% of filing coefficient of steel ball, and virtual specific gravity of steel balls makes a calculation according to 4.3.
(2) (2) The general weight of equipment is calculated according to drawing, and the practical weight is 5-8% more than calculated weight.
Its features in following four aspects:
(1) Bush bearing is replaced by rolling bearing, friction resistance being greatly lowered down, easy to be started and energy saving.
(2) The discharging part is designed as a cone type, which increase the capacity and enforces the material at the discharging end to be reclassified, and the balls are reclassified too, that is the nearer to the end ,the smaller are the balls.increasing repeated milling effect.
(3) Grooved ring liner is adopted ,which increases the contacting surface between balls and material, improves milling effect,and saves energy by its lifting effect to be material.
(4)One-piece frame is used, facilitating engineering construction and equipment installation.
